On this page
- Decide what you want the water to reach
- Compare working pressure and flow together
- Measure the route as the garden is actually used
- Work out the usable water and likely running time
- Check suitability for the tank and what comes in the box
- Compare a sprinkler with a simpler watering option
- Make a shortlist from your own measurements
Decide what you want the water to reach
A water butt can supply a hose or sprinkler when the equipment matches the job. Start by naming what you want to water: a row of containers, a small vegetable bed or an area of lawn. A short hose with a hand nozzle may need a different setup from an oscillating sprinkler you want to cover a wide patch. You might also find that a watering can or a system intended for low-pressure delivery suits the plants more closely.
Choose the sprinkler or hose attachment before choosing the pump. Find the manufacturer’s operating pressure and required flow, including the settings for the coverage you want. If the page gives only a broad claim about coverage, look up the manual or ask the supplier what the attachment needs. Write those figures down with your garden measurements. A pump advertised for rainwater may suit one sprinkler and fall short of another.
Compare working pressure and flow together
Pressure describes what can drive water through the attachment. Flow is the amount delivered, often printed in litres per hour or litres per minute. Convert the figures to the same units before you compare them. A pump’s maximum flow figure and its maximum pressure figure usually refer to different operating points. A useful check is how much water the pump can actually deliver at the pressure you need.
Look for a performance chart or ask the supplier for the working output when the sprinkler is connected. Give them the sprinkler model, hose length and diameter, and whether the sprinkler stands higher than the water. A longer run with restrictive connectors can reduce the water that reaches the attachment. The rise from the butt to the sprinkler also contributes to the head the pump has to overcome. Compare pumps on the route you’ll set up rather than the largest digits on the box.
| Job | Start with | Check |
|---|---|---|
| A few pots near the butt | Watering can | Trip distance and how much to carry |
| Several beds along a path | Compatible pump and hand nozzle | Hose run, pressure and useful volume |
| A row of thirsty plants | Suitable drip kit | Specified pressure, filtration and uniformity |
| A patch you want to water evenly | Pump and compatible sprinkler | Working pressure, flow and running time |
Measure the route as the garden is actually used
Measure from the pump position to the sprinkler position along the path your hose will take. Include bends around a wall or steps and check the difference in height. Note any quick connectors, nozzle or filter the manual specifies. If you split the supply between two attachments, check the combined demand or plan to use them one at a time. A short run with one sprinkler is simpler to compare with the maker’s figures.
Check where the hose will lie when you run it. If it crosses a path or shared route, plan how you’ll keep the area clear. For an electric pump, follow both the pump manual and Electrical Safety First advice for outdoor power. Check manufacturer guidance before using an extension lead or any other power connection. If you’re also considering mains-fed watering, check the supply and route for each setup separately.
Work out the usable water and likely running time
The capacity printed on a butt describes its size. The water available on the day also depends on the level in it and how much the pump can use before its intake or shut-off limit. To estimate the session, divide usable litres by the rate you plan to deliver in litres per minute. In a worked example, 80 usable litres at 8 litres per minute gives about ten minutes. If the actual rate differs, the running time will change with it.
Compare that estimate with the job. If you want to water a strip of pots, a direct delivery method may put more of the stored water where it’s needed. If you want repeated lawn watering, check what the butt can provide between refills and whether a sprinkler is the best way to spend it. The RHS watering guidance explains how plants and soil affect what needs watering and how a hose, can or drip system can suit different layouts.
Check suitability for the tank and what comes in the box
Look for a pump intended for the water source and mounting position you have. Read the instructions for tank fit, water level, filtering and what the unit does when the water gets too low. With a narrow lid or a shallow container, check the dimensions of the pump and fittings. Ask whether the supplied hose connector matches what you’ll use and whether an approved filter or adapter needs to be bought separately.
Some products are explicitly described as suitable for sprinklers. Gardena gives examples of compatible sprinklers on its rainwater tank pump page. Use that as a guide to the type of compatibility information to seek from a manufacturer. If you need a replacement filter or fitting later, find the pump’s full model number and approved part before ordering. The garden-tool spares guide gives you a method for checking part numbers.
Compare a sprinkler with a simpler watering option
A watering can can suit a few containers close to the butt. A hose and suitable nozzle can help when you need to reach several different spots and want to control the water you use. A drip kit can suit a row of plants if the manufacturer approves it for your pressure and source. For some layouts a gravity-fed product may work, provided the system is designed for the available head and the position of the container. Check its filter and maintenance requirements.
A sprinkler is useful when the coverage and rate suit the area you want to water and you have enough stored water for the run. If your main need is a row of containers, compare whole setups before assuming you need that coverage. If you’re thinking of using the same butt for outdoor cleaning, check the pressure washer guide for the separate inlet and accessory requirements a washer may have.
Make a shortlist from your own measurements
Write down the attachment, its working requirements, the size of hose and the rise to the garden. Note the smallest amount of useful rainwater you expect to have and estimate how long the chosen setup would run. Use those checks to ask whether a particular pump suits your plan. Price the fittings and check that you have an approved place to use and store the equipment.
Before you rely on it, follow the maker’s advice on use and maintenance, including keeping the filter clean and protecting the unit when the weather turns cold. Check the arrangements for your water source and your supplier’s current guidance if there are restrictions. Start with the plants you need to water and the water you actually have. That makes it easier to decide whether a pump and sprinkler are worth the setup.